国产精品视频一区二区三区四,亚洲av美洲av综合av,99国内精品久久久久久久,欧美电影一区二区三区电影

產品推薦:氣相|液相|光譜|質譜|電化學|元素分析|水分測定儀|樣品前處理|試驗機|培養箱


化工儀器網>技術中心>行業標準>正文

歡迎聯系我

有什么可以幫您? 在線咨詢

PV1503大眾汽車高溫高壓蒸汽油漆涂層噴射

來源:上海鼎振儀器設備有限公司   2018年01月16日 22:04  

full

凱馳

Changes  The following changes have been made as compared to Test Specification PV 1503, 1998-02: Standard compley revised Contents of PV 1504 added
 
Previous issues  PV 1503: 1987-10; 1996-12; 1998-02; PV 1504: 1990-10
 
1  Scope  This standard describes a procedure to determine paint adhesion on metallic and non-metallic materials. It simulates the stresses produced when surfaces are cleaned with a steam jet using two different tests:  Test A: flat angle of jet along the two intersecting legs of the St. Andrew's cross (see Figure 1) Test B: steep angle of jet in the center of the St. Andrew's cross  The test to be used shall be agreed with the responsible engineering department.  
2  Description  Steam jet test according to PV 1503A, or steam jet test according to PV 1503B.
3  Test method
3.1  Equipment and auxiliary equipment  Steam jet (e.g. Kärcher or NIFAB)  Painted non-metallic parts (e.g. bumper and mirror housing) Painted metallic exterior parts and parts of the chassis Scratch marker per van Laar and Clemen according to DIN EN ISO 7253 Cutter (e.g. Edding, cutter ML 18)
3.2  Specimen preparation
3.2.1  Unloaded steam jet test (as-received condition)   Conditioning of painted plastic parts for 48 h at 50 °C or 24 h at 60 °C followed by aging in the DIN 50 014 – 23/50-2 standard climate.  Conditioning of painted metallic exterior parts and parts of the chassis for 24 h in the DIN 50 014 – 23/50-2 standard climate.
3.2.2  Steam jet test after loading (e.g. 240 h according to DIN 50 017 KK)  Conditioning of the specimens before the steam jet test after loading (e.g. 240 h according to DIN 50 017 KK).  Acclimatization of the plastic parts for 24 h in the DIN 50 014 – 23/50-2 standard climate.
3.3  Test conditions and setting parameters  See Table 1.
 
 
 

1ParameterPV1503APV1503B
1Preset working pressure   (depending on device type and hose length) (90 ± 5) bar
2Outlet temperature   measured 10 cm from the nozzle (60 to 70) ℃
3Impact pressure   measured 15 cm from the nozzle  at an angle of 90°(19 ± 2) N
4Nozzle type   depending on device manufacturerSpraying Systems TP2505 EG  NIFAB  2506
5Distance from nozzle to specimen = 15 cm To be used for paint coatings of any type on plastic and metal on the exterior of the vehicle (requirements according to Technical Supply Specification).
6Distance from nozzle to specimen = 5 cm  To be used for low-temperature paint coating (e.g. 90 °C)  on all substrates, see No. 12 for control limit,  paint flakes
7Distance from nozzle to specimen = 2 cm  To be used for high-temperature paint coating (140°C); control limit and requirement as for No. 6.
8Angle of jet 45°90°
9Duration of spraying Spraying acc. to Figure 1  1 x 20 s, slight  swinging movement, even spraying above the point of  intersection of the St. Andrew's cross.
10Nozzle alignment Along the intersecting legs of the St. Andrew's crossPoint of intersection of the St. Andrew's cross on the  specimen
11Spray pattern   (check of the setting parameters) Material to be used: Styroform RTM from Stadur-Süd GmbH, procedure according to 3.4.1 
12Control limit Paint flakes ≥ 3 mm² and an acceptable  test result at 15 cm (distance from nozzle to specimen) indicate a test result that is still acceptable. However, the paint adhesion of the specimen must be optimized and the specimen must be resubmitted.

 
 
 


3.4 Procedure
3.4.1  Check of the spray pattern  The spray pattern is checked using an extruded polystyrene hard foam (see Section 3.3, Table 1, No. 11) with a closed cell structure and flame-retardant additive. The Styroform block is placed in a clamp and the test is carried out with a distance of 12 cm between the nozzle and the block. The penetration depth of the spray jet shall not exceed 5 mm and the spray pattern length shall not exceed 10 cm.
3.4.2  Procedure with specimens  A crosscut (St. Andrew's cross) is made in the specimen according to DIN EN ISO 7253 (the paint structure must be scribed down to the substrate).  The specimen is then subjected to the steam jet under the conditions specified in Section 3.3.
3.5  Evaluation  The specimen is visually inspected for any evidence of detachment of the paint surface after spraying with the steam jet.  The evaluation is based on the degree of damage (length of the detached area at the St. Andrew's cross in mm). Minor flakes up to 1 mm caused by bad cutting at the crosscut will be disregarded from the evaluation.
4  Referenced standards*)  
DIN 50 014 Climates and their Technical Application; Standard Atmospheres  
DIN 50 017 Atmospheres and their Technical Application; Condensation Water Test    Atmospheres  
DIN EN ISO 7253  Paints and Varnishes – Determination of Resistance to Neutral Salt Spray (Fog)


 

免責聲明

  • 凡本網注明“來源:化工儀器網”的所有作品,均為浙江興旺寶明通網絡有限公司-化工儀器網合法擁有版權或有權使用的作品,未經本網授權不得轉載、摘編或利用其它方式使用上述作品。已經本網授權使用作品的,應在授權范圍內使用,并注明“來源:化工儀器網”。違反上述聲明者,本網將追究其相關法律責任。
  • 本網轉載并注明自其他來源(非化工儀器網)的作品,目的在于傳遞更多信息,并不代表本網贊同其觀點和對其真實性負責,不承擔此類作品侵權行為的直接責任及連帶責任。其他媒體、網站或個人從本網轉載時,必須保留本網注明的作品第一來源,并自負版權等法律責任。
  • 如涉及作品內容、版權等問題,請在作品發表之日起一周內與本網聯系,否則視為放棄相關權利。
企業未開通此功能
詳詢客服 : 0571-87858618
蕲春县| 鹤壁市| 晋中市| 寻甸| 集贤县| 塔河县| 准格尔旗| 紫云| 柳州市| 军事| 苍山县| 麻阳| 克东县| 嘉禾县| 辽源市| 醴陵市| 焉耆| 新兴县| 乡城县| 米脂县| 军事| 河西区| 苏尼特右旗| 水城县| 井研县| 什邡市| 百色市| 吉水县| 长岛县| 彰武县| 多伦县| 治多县| 万源市| 胶州市| 布尔津县| 马关县| 乾安县| 习水县| 喀喇沁旗| 博白县| 曲麻莱县|